The OBDII trouble password of P0335 is well-known as a “hard” code, an interpretation severely detrimental to the procedure of your Accord engine. An ext specifically the DTC P0335 to represent a lack of signal from the crankshaft place sensor. The crankshaft position sensor in your Honda Accord educates your ECU that the crankshaft speed and also current location.

You are watching: 2002 honda accord crankshaft sensor location

Without this data, the engine will either no run or run really poorly. Typical symptoms are difficulty starting or the engine may shut off randomly, developing a really dangerous case for not just the driver but the passengers together well.

Possible causes of OBDII inspect engine irradiate P0335Bad or weak batteryBad StarterBad crankshaft position sensorDamaged sensor harness

Today I’ll be reflecting you just how to service and replace your crankshaft position sensor in a 2000 Honda Accord through a F23A1 VTEC SOHC engine.

The part number for this part is 37840-P0A-A01 for the crankshaft place sensor in your Honda Accord. The can also be uncovered under the part number of 37840-PAA-A01.


*

This How To adjust a Honda Accord Crankshaft place Sensor DIY overview assumes girlfriend have currently removed your driver side engine mount and supported your engine with a jack. Please inspect our how To readjust a Honda Accord timing Belt overview for an ext details.

Before you start our DIY guide on just how To change a Honda Accord Crankshaft position Sensor, you need to disconnect the an adverse terminal on your battery. As stated previously, this overview assumes you have the right to raise and also lower your F23 already, i beg your pardon is causing obligation when transforming your time belt.

*

Unplug your 4 pin connector that runs to her crankshaft position sensor in her Honda Accord. Here’s what your pigtail look at like an installed to her F23A1. It’s secured by a 10mm bolt the runs with the back of her VTEC SOHC engine.

*

This harness to her crankshaft place sensor runs through your lower timing plate, which should be gotten rid of to change a Honda Accord Crankshaft position Sensor. In order to execute this, girlfriend must lower your engine if still connected to her chassis, and remove the crankshaft sheave or harmonic balancer.

This may be complicated if you room working top top the ground through hand tools and don’t have a waiting compressor v the best air tools. Usage a Honda crankshaft wrench, Moroso component number 61805 to correctly loosen your crankshaft bolt there is no air tools.

*

With the bolt removed, you should have the ability to wiggle off your crankshaft wheel and collection it safely come the side. Make sure eliminate your woodruff an essential and store that together safe as your pulley.

*

Now you have the right to remove all the 10mm bolts that hold your lower timing cover in place. Eliminate these distinct bolts and also then make your way to the valve cover, you will require to back off the valve cover bolts the run with to the cylinder head.

Loosen every the valve cover bolts, but do no remove and gently loosen your valve cover. Elevator the valve covering to enable enough space for your upper SOHC VTEC time cover come come off your engine. There are 2 10mm bolts that run with the upper cover to the cylinder head, remove these to loosen your upper timing cover.

*

Now slide turn off your lower timing cover and pull under to relax from her side engine mount. You should now watch your time belt assembly and also your F23A1 balance shafts and belts. The crankshaft position sensor in your Honda Accord is located behind the crank trigger plate.

*

You can take one of two paths to removing your crankshaft position sensor and also replacing it. You deserve to loosen your timing belt tensioner bolt, the longated bolt located in the center of her tensioner arm. This should enable enough slack regarding gently ago off your reduced crank sheave plate and undo the 10mm bolt the holds the crankshaft position sensor in place.

*

If this is no an option for you, examine out our exactly how To change a Honda Accord timing Belt guide on how to properly time and also remove your F23A1 belts to service your crankshaft position sensor.

There are several timing marks for your balance tower that we recommend friend line approximately TDC before removing her balance pillar belts.

See more: Read The Battle Of The Labyrinth Online Book, The Battle Of The Labyrinth

*

Before removing her balance shaft belts come reach your crankshaft position sensor, girlfriend will require to dual check time marks to ensure her F23a1 is at TDC. Again for an ext details check our exactly how To DIY overview on an altering the Honda Accord time belt.

*

Once you have replaced her Honda Accord crankshaft position sensor, you can use a scan device to properly clear her OBDII inspect engine password of P0335. Hope we’ve helped you learn just how To readjust a Honda Accord Crankshaft place Sensor, if you have any kind of questions please leave united state a comment below!